The writer is making a few great annotation about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround in general in the article down the page.
Installing a bath tub isn't precisely rocket science, yet it does require strong plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is additionally a moderately hard job. If the old tub is conveniently available, the task can relocate speedily; if you need to open a wall surface to eliminate the old bathtub as well as position the brand-new bathtub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as embeded in the new one. See to it you have certified yourself for the work and fit attempting it. As opposed to hiring a service provider to take over a halfway-completed task, it is better to think about employing one prior to you start. Possibilities are you might need an expert plumber to make tube connections.
This short article will certainly help you set up a brand-new tub in your washroom if you have currently acquired a new bathtub and don't require to change the plan of your previous water pipes.
Your tools and also material checklist need to comprise the following:
- New Tub
- Hammer
- Pipeline Wrenches
- Prybar
- Safety Glasses
- Level
- Pliers
- Flexible Wrench
- Putty Knife
- Screwdriver
- Cold Blade
- Measuring tape
- Pipeline Caps
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you should do is disconnect the water system. After doing so, activate the taps to drain any type of water continuing to be in the system. The process of removing the existing faucets can be fairly bothersome due to the restricted gain access to that is usually the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a fabric all set for the continuing to be water that will certainly come from the pipes. When the supply pipelines have been removed, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning throughout this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin guaranteeing that the washers are in area in between the faucet as well as the sink. Protect the tap in place with the manufacturer given backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type should be connected to the faucet finishes first, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Making use of the two wooden boards under its feet, position the tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little points.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub up until the spirit level reviews degree.
To install faucets, fit the bottom of the furthest versatile faucet port to the suitable supply pipeline by making a compression join; then do the exact same for the other faucet.
Turn on the water supply and also check all joints and also new pipework for leakages as well as tighten them if necessary. Load the bathtub as well as likewise examine the overflow outlet and the typical outlet for leakages.
Finally, take care of the bath paneling as defined in the producer's user's manual. Tiling and also sealing around the bath tub ought to wait till the bathtub has actually been used at the very least once as this will certainly settle it right into its last setting.
Planning for the Setup
To start with, the supporting structure supplied with the bath needs to be fitted (if needed) according to the supplier's instructions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you use all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its final position.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to split a stiff seal, creating the water to pass through the wall surface in between the bathroom and also the tiling, bring about complications with dampness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and also installations. They are marketed in tubes and also cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of soaked paper or soft rope. Keep in mind to always fill up the tub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealer can break relatively early if you do not take into account this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate reader about A Step-by-Step Guide to Installing a Bathtub, I imagined sharing that piece of content was a good idea. If you enjoyed reading our page please be sure to share it. Thanks a lot for taking the time to read it.
Book 24/7
Comments on “A Step-by-Step Guide to Setting Up a Tub”